looking for a standard exhaust for my rev3 turbo, have a performance one here that ill swap for, sounds lovely, not to loud, i just dont like the single exit....cant really see it on the pic, but its the only pic i have at the mo, ill take a decent 1 2moro.
Im breakin this car if any1 is looking for any bits.......

_KUNENA_BBCODE_HIDEIMG

im looking for a few bits if the price is right.how much for the very front and the back undertrays,the dash clocks,and the front drivers side brake caliper?

Don't have an exhaust for you, but on the subject of breaking.

I am looking for undertrays (Edit: Damn MR.2 beat me to it.), Cigarette lighter enclosure, door central looking switch from inside the doors (drivers side), drivers side red door light, The screws that hold down the engine side panels and probably more but I will look over the car in a minute and figure what else is needed.

Where are you located, and welcome to the club get some pics up of the car your not breaking and whats your plans with it.

Welcome to the site Mitch. I'd be interested in the boot lid and spoiler if they're in good perfect shape (doesn't matter about the paint - only fitment). Where abouts are you located?

well lads,
thanks for the welcome,
suppose il list the bits that arnt there......
engine, box, wiring, ecu.......all the rest is there.
Have a 95 rev3 tbar N/A in better condt so im putting the engine out of this car into it.
All undertrays are there, interior is complete and mint, boot lid and spoiler are perfect, brakes are sticking a bit cause its been lying up for years, only 102,000kms on it.
Im in Offaly.......No1 got a standard exhaust? will part with cash if ya dont wnt my exhaust.......

oh ya didnt realise it was ur first post!welcome how much would you want for just the front undertrays and the undertrays under the engine and oil filter.and how much for the clocks if there reading in kph?cheers

Both cars have good undertrays, neither has the engine one thou. Ill look closer 2moro and i want the better set, u can have the other set for nothin as ill only throw it out.
guess im gonna want the clocks as the other car only has the N/A clocks
Few new parts if any1 lookin,
Brian Crower cams, 264 degrees
HKS adjustable cam pulleys
TODA racing lightened flywheel
ACT paddle clutch rated for up to 500hp
Just rebuilt(all new parts) rev3 engine, not fitted yet, honed block, polished crank, eagle rods, weiseco pistons, ACL main/rod bearings, 1.4mm steel head gasket, BC 264 cams, ARP bolts throughout, new valve springs, valves reseated, new stem seals, new Toyota water/oil pump, every seal/gasket replaced.......

How much are you after for the built rev3 motor ?

Where was the work done on it ? any warranty on the block ?

Ta

Spidey wrote:
How much are you after for the built rev3 motor ?

Where was the work done on it ? any warranty on the block ?

Ta


block was honed and head was skimmed and pressure tested in Condron engineering in Tullamore,
Assembly was done by myself, all parts were new and everything torqued(start to finish full photo rebuild)
Will need a 4000rev 1000mile run in period, another 1000mile on standard boost then it'll be fit for 2bar boost, with suitable turbo/ecu/injectors.
3grand spent on parts, not including the labour and original engine, have to get 2500euro, and warranty wud be strictly conditional!

Ta for the info.

Just another few questions

What size pistons did you use ? And with the 1.4mm headgasket, what does the Compression ratio work out at ?

Has the engine been fired up at all since the build ?

Also, can I ask why you'renot using it ?

Ta
Rob

used 86mm weiseco pistons, original size, cometic steel 1.4 gasket, dont know what the compression ratio works out at,ud have to look into it.
Not been fired up, not been fitted, reason being that ive a corolla 4x4 with st205 GT4 engine and running gear and i built this engine to put into it with the intention of drag racing it and running 500bhp but was let go from work so its not happening now and i need tha cash!!

slipsliderg wrote:
Don't have an exhaust for you, but on the subject of breaking.

I am looking for undertrays (Edit: Damn MR.2 beat me to it.), Cigarette lighter enclosure, door central looking switch from inside the doors (drivers side), drivers side red door light, The screws that hold down the engine side panels and probably more but I will look over the car in a minute and figure what else is needed.

Where are you located, and welcome to the club get some pics up of the car your not breaking and whats your plans with it.


Hey,

Wat part of the central locking mechanism do you need or is it the hole lot. cos i need that part too but if you need a certain part. ye know wat i mean. Did you get the spanners you need.

have 92 turbo exhaust twin E50.00 if you still lookin

where bouts are u? what nick is it in? and will a rev 2 exhaust fit a rev3?

well mitch do you still have the front spot lights or the rear calipers? cheers dan

limrick its fine and should fit i might be going to next meet if ur going?

mitch rear lights and centre panel how much and if your selling na engine how much brother still lookin for rngine for his

actually clocks needed 2

I have a back box if you still need one mate.

tail lights, centre panel, clocks, all gone. calipers i need.
front fogs are there and only the NA rear calipers
most of the NA stuff still there,

here is a pic of th exhaust i dont know which version its off

_KUNENA_BBCODE_HIDEIMG

lambert wrote:
here is a pic of th exhaust i dont know which version its off

_KUNENA_BBCODE_HIDEIMG

Th'is N/A

well if anyone wants this exhaust they can have it free of charge.

well mitch jus wonderin do u still have the front bumper an if so how much? cheers dan

yeah its still there, its got a rev1 splitter thou. 50euro

pm sent

hi would you be splitting the wheels as the fronts are differnt from the back if so how much for the fronts
Cheers

have to get 150 to justify splitting them, good tyres thou. 250ya can have the 4 of em!